Showing posts with label C128. Show all posts
Showing posts with label C128. Show all posts

Sunday, 21 August 2022

Power supplies of the 8 bit generation

During the development of the Minstrel 4D, I started looking at the options for it's power supply. This started off as a short introduction to a post about that. However, once I sat down and started typing, it grew into a significant Patreon post in its own right. The actual article followed in a separate post (or two). I have now expanded this one even more, and also the second part which will follow next week.

As part of the research for an upcoming project, I wanted to look a bit deeper at the various methods of supplying power to 8 bit computers.

ZX80/ZX81

A good starting point is the ZX80 and ZX81.

These both use the same nice and simple power input. A 3.5mm headphone jack is used to take 9V DC. This is then regulated down to 5V with a 7805 and a heatsink. The unexpanded board draws about 200mA (depending on the ROM and RAM chips used). The 9V is not use for anything else but is provided on the edge connector for expansions to use to get their own power.

I don’t know it is was officially specified, but there seems to be a general understanding that if you weren’t using too much power, say less than 50mA, then you could just use the 5V on the edge connector, and the internal 7805 would get a bit warmer. If you needed any more power, you should use your own regulator to generate the voltages you need from the 9V DC. This became more important with things like the 16K RAM packs that used DRAM which required 12V DC and -5V DC, which were generated from the 9V.

The simple 7805 approach works well, and I used the same method on many of the early kits. One thing I changed was the power connector. It can be a bit of an issue as it is right next to two other identical 3.5mm jacks, one for ear and one for mic. It shouldn’t do any damage as there are resistors and capacitors in series with the input, but it will cause confusion when it doesn’t work.

Another issue is the 3.5mm jack will short the two contacts when inserted and removed, so is not ideal for a power supply. I went with the 2.1mm DC jack, centre negative. As used on the ZX Spectrum and Commodore 16 etc. (I will discuss polarity and related issues in the next post)


There is no power switch here, so you either rely on turning the external supply on and off, or you plug and unplug the cable, hence why the 3.5mm jack is a bad idea.

A common upgrade is to replace the 7805 with a switching regulator. This removes any issues with it running warm.

Pros: Simple, cheap, allows for some expansion

Cons: No power switch, shorts on removal / insertion, runs a bit warm.

ZX Spectrum

The Z Spectrum continued with only a Few changes to the ZX80/ZX81 approach. First was the 2.1mm DC jack as previously discussed. The second was to become the Achilles heel of the Spectrum. It had 16K of 4116 dynamic RAM onboard. Like the 16K RAM pack in the ZX81, this needed 12V and -5V. And so, the saga of the Spectrum's switching regulator began. The design of this changed on every revision of the board, and sometimes several times between with mods applied at the factory or recommended to service engineers. Transistor TR4 and TR5 were notorious for failing and losing the +12V and -5V rails which is a good way to kill 4116 DRAM.

The 32K of additional RAM in the 48K models was 5V only. It would have made sense to have switched to using those chips in the lower bank, or the 5V only versions of the 4116 such as the 4516 used in the Atari 5200. (You don't normally see green silkscreen on chips. I wonder if these turn red when they fail?)

I expect they would have considered options like that, but as the edge connector had -5V and +12V, they had to provide those to support add ons that had already been developed. When Amstrad came along, they were less concerned about backward compatibility, so finally dropped those rails from the last generation of Spectrums.

As with the ZX81, a switching regulator can be fitted which will reduce the heat generated (just leaving the ULA to heat the room).

Pros: ….anyone got any ideas?

Cons: unreliable and the cause of failure of a good proportion of Spectrums (+ no power switch)

Commodore PET 2001

In a slightly different direction, going back to the original Commodore PET 2001. This was a fairly straightforward power supply arrangement. A centre tapped transformer provided 9V AC which was rectified by two diodes and fed to a large smoothing capacitor that was not on the mainboard. The 9V actually goes to the capacitor on one red wire, and comes back on another.

From there, it feeds a few 7805 regulators to generate 5V DC for all the logic on board. These had huge vertical heatsinks on and would often run warm, particularly in older machines where the 6540 ROM and 6550 RAM chips slowly fail and start a war of attrition with each other seeing who’s output transistors can win the bus contention argument as they slowly cook themselves.

The 9V DC is also used to power the datasette, giving it a switchable 6V (ish) supply – see a previous post where I go into a lot of detail on the various circuits used for that.

http://blog.tynemouthsoftware.co.uk/2022/06/powering-commodore-datasette-drives.html

Pros: Bomb proof simple chunky design. These things will outlive the cockroaches. Mains powered with mains on off switch.

Cons: Bomb proof simple chunky design. Weighs an absolute ton.

Commodore PET 2001N - 8032

The Commodore PET 2001N onwards also jumped on the 4116 bandwagon, with all the additional complexity that brought. The 9V supply was now full wave rectified to provide a lower current -9V supply which fed a 7905 to generate the -5V rail. An additional secondary winding on the transformer, more diodes and a smaller onboard capacitor provided a 15V supply which was regulated down to 12V with a 7812.

The 5V regulators were swapped out for even beefier TO3 packaged LM340K regulators which could handle several amps at 5V. There were initially two, but later revisions of the board had just a single one of those.

Pros: A more reliable multi rail supply with even chunkier 5V. Mains with power switch

Cons: As before, bulky and heavy, and now additionally complicated

Commodore VIC 20

The first version of the VIC20, referred to as “2 pin” because it had a two pin power connector. This was fed 9V AC from an external transformer. As simple as it could be. On board there was a power switch and the chunky TO3 version of the 7805 with a big heatsink. Like the PET it also used the 9V to generate the 6V for the datasette, and like the Spectrum, it complicated future designs by providing 9V AC for external devices, in this case via the userport.

Side note, they used at least two different connectors, the US version is different to the UK one, not sure about the VIC1001.

Pros: Simple and cheap. Reliable design. Mechanical power switch.

Cons: Even with the big heatsink it does get warm. Takes up a lot of board space.

Commodore VIC 20 CR

The second version of the VIC20 moved the 5V regulator off board into the power supply. This brought with it two problems. Firstly, because of the need to provide 9V AC to the userport, the supply now has to provide 5V DC and 9V AC, so they chose for some reason to use 4 pins of a 7 pin DIN plug. (aside I haven’t really thought about that before, I wonder if there was some lost interim plan to provide -5V and +12V on the same connector, hence the unused pins?)

The second problem is they just seemed to do a bad job with the 5V. Not sure specifically why, there is a resistor in the ground wire on the regulator, and that makes it a lot more susceptible to a failure mode where it passes all of the input voltage to the output. This feeds much more than 5V onto the 5V rail and fries the board. Not to be recommended. Don’t use these supplies folks.

This is such a common problem that there are a few solutions around. One I am not personally keen on is the inline protectors, I am not convinced they would operate fast enough to protect the machine. Another solution is complete after market power supplies which are generally a safer bet.

Another option with the VIC 20 CR (“7 pin VIC”) is to feed it with 5V only. The 9V AC is fed direct to the userport and it’s only use on board is to provide power for the datasette. If you aren’t using anything on the userport that needs 9V AC, and you don’t need a datasette, then a single modern 5V supply is a good way to go. (you can also use a 5V and 12V disk drive type power supply as the 12V DC can be fed where the 9V AC would go and will power the datasette. The TIP 29 will get a bit warmer when the drive is in use, and it may not be suitable for any userport devices, so be wary).

Pros:gets rid of big heatsink. Mechanical power switch

Cons:Danger Will Robinson. Do not use.

Commodore 64

The C64 used the same supply as the later VIC20, but made more use of the 9V AC. Here it was rectified to get 9V DC for the datasette, on some models, an additional 7805 provides a dedicated 5V rail for the video circuits. There is also a voltage multiplier circuit and a 7812 to generate 12V for the SID and the VIC.

Most of the standard C64 power supplies were glued shut and fully potted inside. Making then not only unreliable but also unserviceable.

Some later versions were screwed together, but still partly potted inside.

Pros: Mechanical power switch

Cons: Danger Will Robinson. Seriously, do not use!

Commodore 64C

They simplified things a bit with the C64C, they got rid of the voltage multiplier and lowered the supply voltage to the updated SID and VIC to be 9V.

Commodore plus/4

This uses the same supply (with the same issues) as the C64, but much to the annoyance of the designer, has a square 4 pin DIN instead of the round 7 pin (although early PCB revisions could fit either socket).

This is another of the reasons why this post kept growing. I have converted several of these in the past, but couldn't find any photos, so I ended up converting another one. I took enough photos that it justified a post in it's own right - http://blog.tynemouthsoftware.co.uk/2022/07/commodore-plus4-7-pin-power-conversion.html

Commodore 16

There are various things wrong (or at least less than ideal) with the Commodore 16, but actually the power supply is one of the best.

Nice and simple, 9V DC in, centre negative. Mechanical power switch, 7805 regulator and 6V for the datasette. No external access to the 9V DC, so no issues there.

The external power supply is very much the same as the Sinclair ones, nice and simple, and screwed together so it is full serviceable and even fused.

As unexpected as it might be, I think the Commodore C16 has the best power supply of any of the 8 bit computers. There I have said it. Do you agree?

Pros: Simple reliable design. Mechanical power switch, external supply, serviceable.

Cons: None that I can think of.

Commodore 128

There were a few variations of this, but they basically started to get things right with internal or external switch mode supplies with proper regulation and reasonable efficiency.

The same thing continued into the 16 bit Amiga range.

More on this in an old post on repairing that PSU

http://blog.tynemouthsoftware.co.uk/2014/10/commodore-128-repair-part-1-psu.html

Pros: Internal or external versions, mechanical power switches

Cons: external version for flat C128 is a bit bulky, but worth it for a better quality supply

Atari 5200

I will include this here just because it is very weird. The 5200 used a combined RF cable and power supply.

Let that sink in.

There was a single cable that provided the power and also the TV signal.

In the wider world it’s not that usual, the same thing is used to power the LNBs on domestic satellite dishes etc. But in the 8 bit computer world I think it is unique.

Here the power is combined with the RF signal in a box at the TV end (unpowered switch boxes like that appear to have been more common in the US, I don’t recall seeing them in the UK).

The single thick coax goes to the box where it is split and powers the unit. It does have a nice soft power on circuit. This has a soft touch power button (i.e. not a clunky mechanical switch, but a push on, push off digitally controlled switch), which switches two separate 7805 regulators. One of which is disabled when there is no cartridge plugged in, which is a nice touch that might have saved a few 2600s.

More details in a repair blog from a few years ago

http://blog.tynemouthsoftware.co.uk/2019/01/atari-5200-not-powering-on-repair.html

Pros: Remote power, soft power on, safety cutout on cartridge removal

Cons: Over complicated. Fixed, thick, inflexible RF cord.

The BBC Micro - Early models

Early models of the BBC Micro had a nice linear power supply. This was a toroidal transformer feeding a number of linear regulators. I think there were 7805s. I don't know as all the ones I have are both riveted shut and still working.

I think these were used on the Model A, which had no disk drive, so no need for the disk drive power, which was not present on these models. 

More about the BBC Model A - http://blog.tynemouthsoftware.co.uk/2019/06/bbc-micro-issue-2-model-a.html

Pros: Nice simple solid design. External power switch

Cons: Messy internal wiring with several spade connectors scattered around the board. No disk drive power.

BBC Micro - Issue 3 onwards

The power supply was changed to a nice switch mode supply in most models. Mains powered, on off switch. All very good.

But, they use RIFA filter caps. And they go bang. They always go bang. If they haven't yet, they will. Don't think "I'll give it a quite try first". No, always replace them before powering on, or you will regret it for the next day or so until your house stops smelling of burned capacitors.

There is also another capacitor which is a bit close to a heatsink that has a tendency to fail as well and stops the power supply starting up.

More info here

http://blog.tynemouthsoftware.co.uk/2017/05/bbc-micro-power-supply-repair.html

Pros: Switch mode supply. Power switch.

Cons: The grim Rifa.

Amstrad CPC 464


This one starts well, 5V DC in. Nice and easy.

But dear old Sir Alan didn't just want to sell you a computer. Not happy with gluing a tape deck to the side of it, he wanted to sell you a telly as well.

So the power for the CPC464 comes from the TV, with a two wire arrangement, one plug is for the RGB video out of the computer, and one is for the 5V power.

If you aren't using the Amstrad monitor / power supply, you can use an external 5V supply.

Pros: Neat if you are using the whole system

Cons: Messy if you are not using the whole system, expensive if you already have a TV you could have used.

Amstrad CPC6128

The success of the CPC464 was followed up but the slightly more complicated CPC6128. This had a built in disk drive, which also needed 12V, so as well as the two existing wires the came from the TV, there was a third which came from the computer and plugged into the TV.

This was messy when used with the Amstrad monitor, and when trying to use it without the monitor it's just plain silly.

Pros: Not as bad as the GX4000

Cons: Messy either way

Amstrad GX4000

I don't actually have one of these, but I understand they had two DC jacks on the back, two power supply options, 5V from one of the CPC464 tellies, or 9V DC from a power supply. In theory, one is 2.1mm and one is 2.5mm, so you can't plug the supplied power cable into the wrong jack, but guess what? People will use anything that fits, and plug the cable into the wrong one and bang.

Pros: Any fans of the GX-4000?

Cons: Two power input jacks. Nice idea.

Oric 1 / Atmos

This is unfortunately one of the most problematic. For no good technical reason that I can see, and possibly due to cost or supply, they used a 7905 -5V regulator to generate the +5V DC.

I will go into the issues with this in the following post. Like many of these system, it is fine if used in isolation with the correct supply, but if you change things, it gets complicated.

Pros: There must have been one at the time

Cons: Potential problems with voltage offset of the 0V rail.

What have I forgotten?

Congratulations if you made it this far. Quite a lot going on there, and there are many more I could have included. What have I forgotten? any other weird and wonderful options? Should I have split this up? I did start to add schematics to some of them, but then it gets a bit silly.

Next Up

I will leave it there. The next stage is to look at the modern versions on the Minstrel and Mini PET and what options to consider for a future project, including USB power, input polarity, bridge rectifiers and the whole Oric thing.


Advertisements

Spoiler alert - the Minstrel 4D did not end up being USB powered (although one of the prototype boards was).

http://blog.tynemouthsoftware.co.uk/2022/08/minstrel-4d-overview.html

The 4D is available for pre-order now from The Future Was 8 bit.

https://www.thefuturewas8bit.com/minstrel4d.html

Patreon

This post is an updated and extended version of a post from my Patreon. If you want advance previews of posts like this and behind the scenes progress on new projects, you can follow along and support me on Patreon:

https://www.patreon.com/tynemouthsoftware

Sunday, 16 December 2018

Commodore 128 Keyboard repairs

This is an old post, preserved for reference.
The products and services mentioned within are no longer available.

It's about time I did something about the keyboard on my Commodore 128D. It does the job, but there are a few issues with it.
Firstly, the + key is missing from the numeric keypad, and the key stem is broken.
And also, the Caps Lock switch is a latching switch and that is completely missing
The other issue is this is not the standard UK keyboard, it seems to be a German QWERTZ keyboard, with the alternates on the Z and Y keys.
The symbols keys are just mad though, what's going on there? 0 = and 0 again on the 0 key, * * and + and the * key, Eh? I just don't understand what is going on there, and it's a bit of a pain to find the right one when typing.
To help with this, I have a keyboard from a broken slightly yellowed flat C128. I'm a bit scared to remove that address label on the bottom as it looks to have been there a long time, so will probably be a different colour underneath.
This one also has issues. Caps Lock is present, but all the other buttons next to it are broken off. The top row of keys stick up the most, so are often the ones to get damaged in storage (or when being pulled out of a skip).
Apart from the function keys on the end, they are C128 mode only, and are not recognised in C64 mode (even the arrow keys are ignored). The 40/80 key is there, but again is alone in it's group, and also the switch is broken.
The function keys are all there, two of the arrow keys are missing and the ; ) key is stuck down and repeating.
The keyboards are actually almost identical, the main difference being the cable. On the C128D, this is a two foot cable with a 25 way D male connector on.
On the flat C128, it is a six inch cable with a sort of square 25 way D female connector on.
The same PCB was used for the flat C128 and the original C128D, with either a pin header for the internally connected keyboard on the flat C128 (below).
or a right angled 25 way D female on the C128D (above).
As with most Commodore keyboards, to do anything with these involves desoldering the connections to the latching switches (three of them on the C128 boards) and removing hundreds of tiny screws.
Whilst it's apart, it's a good opportunity to give the contacts a good clean.
Putting it back together, I added some tape over the place where the cables were soldered on. All the VIC20 / C64 keyboards had this from the factory, but neither of these 128s did.
The metalwork is identical, so I ended up swapping the PCBs around to make things easier. They both have the same mounting holes and angled sections etc. so it's was a straight swap. I used the key stems from the two top row arrow keys and the - on the keypad to replace the broken / missing ones on the good keyboard and to provide the most useful keys on the other.
I have rearranged things to give one standard UK keyboard with a full set of key switches, and one made from the leftovers, including all the QWERTZ keys with the extra symbols on. (and before anyone asks, I don't have any spare keys available. Every time I do a post like this, I get people asking for spare keys. Sorry, as you can see I've used them all)
I had been asked for a Commodore 128 USB keyboard controller, so that was another reason why it was a good time to run through this as I had it around for testing. I've built a few of these C128 USB keyboard controllers, but not enough to have done a custom PCB (yet), so this is adapted from one of the my generic boards with a 25 way D connector on a ribbon cable. I have used a 25 way D male IDC connector with the shell removed. It's not a perfect match for the pin header on the C128 board, but it works fine.
The board with the leftover keys has all the keys required for C64 mode, and the caps lock switch moved along with the 40/80 cap on it as the 40/80 switch is rather important - how many C128s are thought to be broken because 40/80 has been pushed down and it's in 80 column mode.....
That all tested fine, so will be quite handy as a keyboard for bench testing C128 boards, when I won't be too bothered about the extra symbols or missing C128 mode keys.
To test the good keyboard I will be using for my C128D, I used an alternate ribbon cable (if I tell you the 25 way D connector was purple, can you guess where it came from?).
That also tested all fine, so back into the case and it looks alright. A bit yellowed, but evenly so, and not obviously made up of bits of two keyboards.
I know I have tested it as a USB keyboard, but I wanted to retest it on the C128D itself.
That's all back together with the similarly yellowed C128D-CR and a 1901 monitor.
And yes, of course I tried out Rodman.
The CRT monitor is always nicer to look at, and clearer in the s-video and RGB modes the C128 generates, but I still tend to use pictures from an LCD monitor in these posts as it is easier to photograph, apart from in C64 mode, where the light blue on dark blue colour scheme rather confuses my camera.
Sometimes on these posts I end up with a folder full of unusable photos as I try to surprise the camera by coming at the screen at different angles.
Sometimes I give up and have to cheat and poke the VICs background colour register to black (see next week's blog post...)