Showing posts with label TV Game. Show all posts
Showing posts with label TV Game. Show all posts

Sunday, 6 May 2018

Binatone TV Master Mk 8 TV Game Composite Video Conversion

This is an old post, preserved for reference.
The products and services mentioned within are no longer available.

I have done several TV Game composite video conversions recently, and they have all been pretty much the same, locate the composite video signal feeding into the modulator. Disconnect or remove that and fit a composite video buffer board to drive the TV.
I've done black and white ones, and colour ones, this one is monochrome, with greyscale, but that should be the same, shouldn't it?
Well, no, this one turned out to be quite a problem. I always start by testing these systems on an old CRT TV, to make sure they work. You can see from the picture above that this has a grey background, white text and black text.
I fitted the usual composite video board, but when I tried it, I only got black and white, no grey.
I went over this and checked it out. The composite video board was doing it's job correctly. The input signal was the same as the output. I also checked the signal without the buffer, and back on the old style TV.
It seems the levels were all a bit wrong. Old TVs were very forgiving with poorly formed composite signals, modern ones much less so. The 'back porch' signal, the lower flat section at the start of each line, should be setting the black level. That was almost as low as the sync pulse before it. Anything following at that sort of level should be displayed as black, the highest peaks would be white, and anything inbetween in grey. (the back porch is the thing missing in the ZX80 and early ZX81s that give a very washed out picture on a modern TV set without some changes - more on that in an earlier blog). Here, none of the signal goes near the black level, and the rest is small white peaks on grey.
I thought it might be the chip at fault (there's not much else on there), so I tried swapping the chip with another (from a colour TV game), and the chip worked fine in that system, and that system's chip produced a bad output on this one. The main difference in the colour version is it had an Aztec PAL colour encoder board to generate the colour burst, the rest is the same. (yes, the pin is meant to be missing, it's used on the AY-3-8610 version of the chip to enable the light-gun games which the cheaper AY-3-8600 doesn't have)
I tried various options, including various ways of capacitively coupling the output, and even a convoluted Op Amp circuit to try to boost the signal in the relevant areas, but still got essentially a black or white signal. No grey.
Checking the datasheet for the AY-3-8600, showed the recommended circuit. I suppose it comes out of the way the signal are generated, but it's really quite neat. You get separate outputs for the different parts required, one pin will be high when it should be drawing a bat, one when it should be drawing the ball etc. You can combine these how you like, or could probably drive TTL RGB quite nicely with some minimal circuitry. It's also interesting to see there is no connection to 'left video', which presumably means that will be black, as the other outputs will be off at that point.
Checking the board showed a different approach. They had omitted the buffering transistor, and the values used on the resistors combining the signals were different, higher values in a different ratio.
Running out of ideas, I decided to try swapping those resistors and matching the reference design. I didn't have exact matches to hand, so made up 2.4K using two 1.2K resisters and 1.6K with 1.5K + 100R. Not the neatest solution but the values were right.
I also added a buffer transistor on the back of the board, following the reference design, rather than using the buffer board.
With those changes. the signal was now showing a better range with white peaks, black peaks going down to the back porch set black level, and a grey generally in the middle.
On the screen, shades of grey as it was meant to be. Not sure why the values on the original board were so wrong, but the reference design works fine.
As a side note, many of these Binatone systems have warnings of the dire consequences of not using their mains adapters. It's unclear what the redacted model number was, but it is stamped 02/5011 below, as seen on the last working sticker when I opened one up on a previous unit and found a 7808 regulator in there.
This time, I see nothing, even though the box says it is the right adapter for the TV Master Mk.8. Centre tapped half wave linear power supply. I suppose the resistor across the smoothing capacitor would stop the voltage getting too high off load maybe? At least it has a fuse (3A though) and a thermal fuse.

Binatone Superstar 'Programmable' TV Game Composite Video Mod

This is an old post, preserved for reference.
The products and services mentioned within are no longer available.

One of the more unusual of the TV Games I have been adding composite video modifications to is the Binatone Superstar.
This is described as 'Programmable', and has a selection of 'Cartridges'. I have seen something similar before where the 'cartridges' contained just shorting links, and all the games were on the main chip inside the system.
This one is different though, inside there system there really isn't that much. A pair of 4069 hex inverters isn't enough to run a TV game.
The other main parts are the PAL colour encoder board and UHF TV modulator. Again, not enough for the TV game.
Other than that, there is just the cartridge slot. I noticed it is the same size and pitch as the VIC20 cartridge, although without a 6502 or a VIC chip or anything else in there, this will not work. Do not try this.
What should actually be in there is the 'Super Ten' cartridge.
So the magic must be inside the cartridge. I then remembered a couple of years ago, I saw a YouTube video on this, from Stig's World, where he had opened one up, and had kindly sent me the cartridge he had opened up.
The label had been removed as that was covering the screws, so lets have a look inside this one. Yes, rather more than the shorting links I had first expected.
The chip in there is the AY-3-8610, a TV Game on a chip. This is from the same family as the AY-3-8600 and AY-3-8500 chips normally found in the non-cartridge systems.
So I'm not sure about 'programmable', but it is certainly 'cartridge based'. I guess if you had nothing better to do, you could build a 'cartridge' with a Raspberry Pi zero in and use this to run some TV game emulators. No, mustn't do that. Too much to do.
I guess you could also make a small box with an edge connector socket on that you could plug one of these cartridges into and get rid of the massive base station. No, too much to do....
The first thing to do is make this work on a modern TV, so it's out with the UM1111 and on with a composite video buffer board (one of the ones from The Future Was 8 bit).
And time for some colour football. This is unsurprisingly the same set of games as most of the other systems, you just get a keypad to select the titles from, rather than a rotary switch.
Other cartridges in the range included a 'Brands Hatch' racing game, 'Stunt Rider' motorcycling racing and 'Knockout' a breakout style game.

Sunday, 25 February 2018

Binatone TV Master 4 plus 2 (MK VI) Composite Video Conversion

This is an old post, preserved for reference.
The products and services mentioned within are no longer available.

Following on from the composite video conversion I did a few months ago on a Radofin tele-sports TV game, I have modified quite a few other TV games of a similar type.
I bought this one as it is the same model we had back in the seventies when we all looked just like the family on the box.
This one is a Binatone TV Master 4 plus 2, which is the same as the TV Master MK VI. This is similar to the original 4 game version (TV master MK IV), but with two additional games which use a light pen style gun.
The main unit on the 4 plus 2 is identical to the MK VI other than the label. The 4 plus 2 was a cheaper version where the light gun was an optional extra. The gun works in the same way as a light pen, and depends on the timing of the beam on a CRT screen to determine it's position. It will still work following the composite video conversion, but only on CRT televisions.
This is the black and white version, there was a colour version which looked almost identical but was marked 'Colour TV Game', and had white / grey box and buttons rather than the very 1970's day-glo orange. (date code on the chip is August 1978).
Inside is the usual General Instruments GIMINI AY-3-8500 chip, here as they often are in an unusual socket arrangement with no contacts on the four edge pins (they are used on later versions for 2 axis controls).
This was one of the few of these TV games I have found that didn't work. The sound was working, so it was playing, but I couldn't tune in the TV (even the old black and white portable I use for testing things with very poor video signals). The 'scope showed a valid composite signal entering the modulator section, so I just went ahead with the composite video out conversion, there seemed little point in repairing the modulator.
I tried something slightly different on this one, and fitted a header and a socket to the standard TFW8b composite video buffer board, that seemed to work quite well. The power was tapped at the bottom of the board, the video from the point it enters the modulator section, and the audio directly from the chip output.
The unit has a separate switch to turn off the internal speaker, so the audio is always fed to the TV set, but you can also turn on the speaker on the game itself if you want 'the full experience'.
Once powered up, there is a nice stable signal on the monitor, in glorious black and white.
The controls on this version are as simple as they get. One rotary control, and a mono 3.5mm jack.
An inside, one 1MΩ variable resistor. This one was was a bit flaky, but a squirt of contact cleaner and turn it back and forth a few times and it's now running fine.
Binatone like to put warnings on the back of these to get you to only buy their power supplies.
Is it regulated? Is it really? Looks like a standard unregulated linear power supply.
Well, I stand corrected. Yes that is a regulator. A bit rusty, but a regulator none the less.
A National Semiconductors LM342P-8.0, a bit like a 7808. This gives an 8V output which matches the case, although not the 9V the game specified, should be fine...
Time for some two player testing. The only time you will find football on my TV.